app_weld_set_interface_eip_r2m_test(gas_test=[0,0,0,0,0,0,0,0,0], inching_plus=[0,0,0,0,0,0,0,0,0], inching_minus=[0,0,0,0,0,0,0,0,0], blow_out_torch=[0,0,0,0,0,0,0,0,0], simulation=[0,0,0,0,0,0,0,0,0], ts_opt1=[0,0,0,0,0,0,0,0,0], ...)
Features
This sets the communication interface setting to use welders that support EtherNet/IP communication. This sets the interface related to the test signal setting in the communication data sent to the welder from the robot controller. Additional functions related to the test signal can be added with the option item (ts_opt1, ts_opt2). Enter the setting values below along with details based on the communication signal data sheet of the corresponding welder.
Note
To ensure proper welding using an EtherNet/IP remote control welder, all of 8 interface commands must be set up.
app_weld_set_interface_eip_r2m_process(), app_weld_set_interface_eip_r2m_mode(), app_weld_set_interface_eip_r2m_test(), app_weld_set_interface_eip_r2m_condition(), app_weld_set_interface_eip_r2m_option(), app_weld_set_interface_eip_m2r_process(), app_weld_set_interface_eip_m2r_monitoring(), app_weld_set_interface_eip_m2r_other()
Parameter
| Parameter Name | Data Type | Default Value | Description |
|---|---|---|---|
gas_test | Refer to the table below | Refer to the table below | Gas Test Signal (specification for each welder) |
Inching_plus | Forward Inching Signal (specification for each welder) | ||
Inching_minus | Reverse Inching Signal (specification for each welder) | ||
blow_out_torch | Torch Cleaning Signal (specification for each welder) | ||
simulation | Mock Welding Signal (specification for each welder) | ||
ts_opt1 | Option Signal (specification for each welder) | ||
ts_opt2 | Option Signal (specification for each welder) |
The data type, default value and description are identical to the below
Parameter Name | Data Type | Default Value | Description |
|---|---|---|---|
list(int[7]) | 0 | Not Used: 0 Used: 1 | |
0 | Data Type (on/off: 0, Select: 1, Value: 2) | ||
0 | Data Digits (1: 0, 0.1: 1, 0.01: 2) | ||
0 | Communication Data Point (byte): 1~255 | ||
0 | Communication Data Point (bit): 1~255 | ||
0 | Data Size 1-bit(disable Low): 0 1-bit(disable High): 1 2-bit: 2 4-bit: 3 8-bit(byte): 4 15-bit: 5 16-bit(short): 6 32-bit(int): 7 | ||
0 | Valid Data Size Value (bit) | ||
list(float[2]) | 0 | Minimum Data Value | |
0 | Maximum Data Value |
Note
For examples of data (0~2) interface settings, refer to the app_weld_set_interface_eip_r2m_process() section.
Return
| Value | Description |
|---|---|
0 | Success |
Negative Value | Failure |
Exception
| Exception | Description |
|---|---|
DR_Error (DR_ERROR_TYPE) | Parameter data error |
DR_Error (DR_ERROR_VALUE) | Invalid parameter value |
DR_Error (DR_ERROR_RUNTIME) | C Extension module error |
DR_Error (DR_ERROR_STOP) | Program terminated forcibly |
Example
app_weld_set_interface_eip_r2m_test(gas_test=[1,0,0,0,6,0,1,0,0], inching_plus=[1,0,0,1,0,0,1,0,0], inching_minus=[1,0,0,1,2,0,1,0,0], blow_out_torch=[1,0,0,0,7,0,1,0,0], simulation=[0,0,0,1,7,0,1,0,0], ts_opt1=[0,0,0,0,0,0,0,0,0], ts_opt2=[0,0,0,0,0,0,0,0,0])
Related commands
- app_weld_set_interface_eip_r2m_process(welding_start=[0,0,0,0,0,0,0,0,0], robot_ready=[0,0,0,0,0,0,0,0,0], error_reset=[0,0,0,0,0,0,0,0,0])
- app_weld_set_interface_eip_r2m_mode(welding_mode=[0,0,0,0,0,0,0,0,0], s_2t=[0,0,0,0,0,0,0,0,0], pulse_mode=[0,0,0,0,0,0,0,0,0],wm_opt1=[0,0,0,0,0,0,0,0,0])
- app_weld_set_interface_eip_r2m_test(gas_test=[0,0,0,0,0,0,0,0,0], inching_plus=[0,0,0,0,0,0,0,0,0], inching_minus=[0,0,0,0,0,0,0,0,0], blow_out_torch=[0,0,0,0,0,0,0,0,0], simulation=[0,0,0,0,0,0,0,0,0], ts_opt1=[0,0,0,0,0,0,0,0,0], ...)
- (2.11.2_temp-en_US) app_weld_set_interface_eip_r2m_condition(job_num=[0,0,0,0,0,0,0,0,0], synergic_id=[0,0,0,0,0,0,0,0,0], r_wire_feed_speed=[0,0,0,0,0,0,0,0,0], voltage_corret=[0,0,0,0,0,0,0,0.0,0.0], dynamic_correct=[0,0,0,0,0,0,0,0,0])
- (2.11.2_temp-en_US) app_weld_set_interface_eip_r2m_option(opt1=[0,0,0,0,0,0,0,0,0], opt2=[0,0,0,0,0,0,0,0,0], opt3=[0,0,0,0,0,0,0,0,0], opt4=[0,0,0,0,0,0,0,0,0], opt5=[0,0,0,0,0,0,0,0,0], opt6=[0,0,0,0,0,0,0,0,0],...)
- app_weld_set_interface_eip_m2r_process(current_flow=[0,0,0,0,0,0,0,0,0], process_active=[0,0,0,0,0,0,0,0,0], main_current=[0,0,0,0,0,0,0,0,0], machine_ready=[0,0,0,0,0,0,0,0,0], comm_ready=[0,0,0,0,0,0,0,0,0])
- app_weld_set_interface_eip_m2r_monitoring(welding_voltage=[0,0,0,0,0,0,0,0,0], welding_current=[0,0,0,0,0,0,0,0,0], wire_feed_speed=[0,0,0,0,0,0,0,0,0], wire_stick=[0,0,0,0,0,0,0,0,0], error=[0,0,0,0,0,0,0,0,0], ...)
- app_weld_set_interface_eip_m2r_other(opt1=[0,0,0,0,0,0,0,0,0], opt2=[0,0,0,0,0,0,0,0,0], opt3=[0,0,0,0,0,0,0,0,0], opt4=[0,0,0,0,0,0,0,0,0], opt5=[0,0,0,0,0,0,0,0,0], opt6=[0,0,0,0,0,0,0,0,0], opt7=[0,0,0,0,0,0,0,0,0],...)