3.7.1 3.7.0 3.6.0 3.5.0 3.4.0 3.3.0 3.2.2 3.2.1 3.2.0 1. M/H Series 2. A Series 3. E Series 4. P Series Korean English Chinese Czech Dutch French German Hungarian Italian Japanese Polish Portuguese Spanish
3.7.1 3.7.0 3.6.0 3.5.0 3.4.0 3.3.0 3.2.2 3.2.1 3.2.0 1. M/H Series 2. A Series 3. E Series 4. P Series Korean English Chinese Czech Dutch French German Hungarian Italian Japanese Polish Portuguese Spanish

Robot Specifications

Robot operating space

P3020

image2024-6-17_13-7-47.png
image2024-6-17_13-8-22.png


Max. Payload within operating space

The maximum payload of the robot within its operating space changes according to the distance from the center of gravity. Payload per distance is as follows:

Note

This load diagram assumes a small tool load volume. Tools with a larger volume will have greater limitations in payload above the tool’s center of gravity compared to a tool with an equal weight but smaller volume, and in such cases, vibration may occur.


P3020

image2024-7-2_19-43-28.png

Allowed Moment and Inertia

The allowed moment and inertia for the J4-J6 robot are as follows:

Model Name

J4

J5

J6

Allowed Moment

Inertia

Allowed Moment

Inertia

Allowed Moment

Inertia

P3020

 -

-

55 Nm

3.1 kg㎡

36 Nm

2.0 kg㎡

Note

  • For P3020, the tilt (J5) angle is limited based on the tool weight and center of gravity set in Tool Weight, so that the moment applied to J5 when the tool is tilted does not exceed the allowed moment of J5.

  • The limited range is around the posture where the tool is close to horizontal (where the center of gravity of the tool is farthest from the J5 axis). If the tool is light or its center of gravity is close to the J5 axis, the limit is not applied.

  • If the robot enters the limited range during motion, it stops with Stop Category 1. For the travel distance during stopping, refer to the P3020 Stop Category page.

  • The payload diagram is based on the tool-down posture. The tilt angle limit may be applied even to a tool within the range of the diagram.

Tool Center Point (TCP)

Refer to the figure below for TCP.

image-20240909-102934.png


Basic specifications

Model Name

P3020

Weight

83 kg

Payload within Work Radius

30 kg

Max. Work Radius

1900 mm

Number of Axes

5

Max. TCP Speed

Over 1 m/s

Position Repeatability (ISO 9283)

±0.1 mm

Protection Rating

IP 54

Noise

< 65 dB

Installation Direction

Floor Only

Controller and Teaching Pendant

Doosan Controller & Teach Pendant

Vibration and Acceleration

10≤f<57㎐ - 0.075mm amplitude

57≤f≤150㎐ – 1G

Impact

Max Amplitude : 50㎨(5G)

  • * Time :30㎳ , Pulse : 3 of 3 (X,Y,Z)

Operating Temperature

0 ℃ ~45 ℃ (273K to 318K)

Storage Temperature

-5 ℃ ~50 ℃ (268K to 323K)

Humidity

20% ~ 80%


Axis Specifications

Model Name

P3020

Operating Angle

J1

±360° (TP:±360°)

J2

±125° (TP:±95°)

J3

±160° (TP:±135°)

J4

-

J5

±360° (TP:±135°)

J6

±360° (TP:±360°)

Max. Speed per Axis (rated payload operation)

J1

100 °/s

J2

80 °/s

J3

80 °/s

J4

-

J5

200 °/s

J6

360 °/s